York CSA DH 036 Spécifications Page 93
- Page / 140
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2-63
JOHNSON CONTROLS
FORM 102.20-N1 (1109)
2
FIG. 2-95 – RECOMMENDED DISCHARGE DUCT ARRANGEMENT WHEN TURNS ARE REQUIRED
GASKET OR SEALANT
GASKET OR
SEALANT
FLANGED DUCT
RAW EDGE DUCT
SHEET METAL SCREW
DETAIL A
BOTTOM VIEW OF UNIT
DUCT CONNECTIONS
Ducts must have positive seal to unit openings.
Installer is responsible for providing ductwork to include base rail height for curb mounted
units.
All duct work is to be supported independent of the connection to the unit.
If the entire unit is mounted on isolation, the duct connection is to be flexible.
This instruction is suitable for bottom, end, side and top connections. Top connections on
Outdoor units are not recommended.
FLANGED DUCTS OR SLEEVES:
To use flanged duct or sleeve be sure there will be access on all four sides to fasten the flange completely.
:
Flanged ducts can be connected with self drilling screws directly to the unit with gasket or sealant between unit and
duct flange.
A flanged sleeve may be dropped through the opening, provided there is access to seal & fasten the flange to the
unit interior surface.
RAW OR STRAIGHT EDGE DUCTS OR SLEEVES
The duct opening on the unit is located in a panel that is approximately 2” thick. The inside of the opening (2”
surface) is suitable for attaching ducts.
If access is not available from inside the unit, access may have to be from inside the duct or sleeve.
Raw or straight edge ducts can be connected with self drilling screws directly to the unit with gasket or sealant
between unit and duct.
LD14087
Duct Connections
Ducts must have positive seal to unit
openings. Installer is responsible for
providing ductwork to include baserail
height for curb mounted units.
All duct work is to be supported in-
dependent of the connection to the
unit. If the entire unit is mounted on
isolation, the duct connection is to be
exible. This instruction is suitable for
bottom, end, side and top connections.
Top connections on Outdoor units are
not recomended.
Flanged Ducts or Sleeves
To use anged duct or sleeves, be sure there will
be access on all four sides to fasten the ange
completely.
Flanged ducts can be connected with self drilling screws
directly to the unit with gasket or sealant between unit
and duct ange.
A anged sleeve may be dropped through the opening,
provided there is access to seal and fasten the ange to
the unit interior surface.
Raw or Straight Edge Ducts or Sleeves
The duct opening on the unit is located in a panel that
is approximately 2" thick. The inside of the opening
(2" surface) is suitable for attaching ducts.
If access is not available from inside the unit, access
may have to be from inside the duct or sleeve.
Raw or straight edge ducts can be connected with
self drilling screws directly to the unit with gasket or
sealant between unit and duct.
- YORK SOLUTION 1
- AIR HANDLING UNITS 1
- IMPORTANT! 2
- TABLE OF CONTENTS 5
- JOHNSON CONTROLS 10
- FORM 102.20-N1 (1109) 10
- LIST OF FIGURES 11
- LIST OF FIGURES (CONT'D) 12
- LIST OF TABLES 15
- INTRODUCTION 17
- SEGMENT IDENTIFICATION 19
- Solution Unit Model Number 20
- AHU 9-10 21
- 1.0 PRE-INSTALLATION 23
- OFFLOADING LONG UNITS 24
- Shackles 25
- Pre-installation 28
- 2.0 INSTALLATION 31
- LD09616G 34
- Housekeeping Pad 35
- 2-3, 2-4 and 2-5) 35
- General Requirements 36
- ASSEMBLY OF SHIPPING SPLITS 37
- SPLIT ANGLE 45
- WHEN AT SHIPPING SPLIT 47
- (see Fig. 2-25) 48
- Connectors 49
- BOTTOM TIER 51
- FIG. 2-29 – TIERED UNIT 51
- (ENERGY RECOVERY WHEEL SHOWN) 53
- JACKSHAFT TO 55
- BLADE LINKAGE 55
- LD12029A 56
- DAMPER SHAFT EXTENSION KIT 57
- P/N 026-33715-002 57
- Apply gasket 60
- AIR HANDLER 60
- LD12560A 61
- LD12034C 61
- LD12561A 61
- LD12035A 62
- Application 63
- RECOVERY WHEEL 67
- LD11594A 69
- FIG. 2-64 – HUMIDIFIER POINTS 73
- 74
- SIDE CONNECTIONS 75
- VIFB and IFB 80
- Freezing Conditions 81
- Shipping Bolts (VIFB Only) 81
- Interlaced 85
- Row Split 85
- Face Split 85
- STANDARD 86
- 1 inch plus fan total 91
- static pressure 91
- Effective Duct Length 92
- DETAIL A 93
- BOTTOM VIEW OF UNIT 93
- FLANGED DUCTS OR SLEEVES: 93
- FIG. 2-97A – TYPICAL FILTERS 95
- 2-13/16"2-13/16" 96
- Single Filter Application 97
- Installation 100
- DO NOT USE 101
- 029-22081-000 104
- 029-22082 104
- LD06646A 105
- 3.0 STARTUP 107
- ENCLOSURE DOOR 108
- TIE DOWN BOLTS 109
- FIG. 3-5 – SPRING ISOLATOR 110
- FIG. 3-6 – SEISMIC SNUBBER 110
- ForM 102.20-n1 (1109) 111
- ELEVATION VIEW 115
- PLAN (TOP) VIEW 115
- FIG. 3-12 – SEGMENT RETAINER 116
- FIG. 3-15 – SET ID FAN DAMPER 119
- PRESSURE 119
- TEMPERATURE AND EFFICIENCY 120
- TEST PORT 120
- FIG. 3-19 – DAMPER ACTUATOR 121
- FIG. 3-20 – CONDENSATE DRAIN 121
- GAS LP = 2,500 BTU/ CU FT 123
- NATURAL = 1,000 BTU/ CU FT 123
- STEP 1 STEP 2 127
- FOR REFERENCE ONLY 128
- 131
- TOP VIEW OF UNIT 132
- YORK SOLUTION INSTRUCTIONS 135
- START-UP 135
- 136
- 136
- Replaces 102.20-N1 (1108) 136
- APPLICATION INFORMATION 137
- MECHANICAL INSTALLATION 137
- ELECTRICAL INSTALLATION 137
- FORM 102.20-N1 (509) 138
- AIR FLOW REQUIREMENTS 139
- OPERATION & MAINTENANCE 139
- 102.20-N1 (509) 140
Produits connexes et manuels pour Climatiseurs à système divisé York CSA DH 036
(16 pages)
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.175 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels